WTB door frame

42GPW · Unread post by **42GPW** » February 27th, 2014, 11:05 am

Looking for a door frame for the passenger side m151a1. Just need the frame no skin.

Matt R

HILLBILLY-06 · Unread post by **HILLBILLY-06** » March 17th, 2014, 5:28 pm

42GPW wrote:Looking for a door frame for the passenger side m151a1. Just need the frame no skin.

Matt R

I think I noticed where tnjmurray.com has some door frames and they didn't seem too expensive at the time when I say them, maybe check there if you hadn't already...

Eddie Holland · Unread post by **Eddie Holland** » April 15th, 2014, 7:01 pm

Did you find a door frame? I have quite a few.

Unread post by **rickf** » April 15th, 2014, 7:28 pm

Where are you located? I might be interested in a door frame as long as it does not have to be shipped. That might be expensive.

42GPW · Unread post by **42GPW** » April 15th, 2014, 8:45 pm

Eddie Holland wrote:Did you find a door frame? I have quite a few.

no I did not. I need a complete passenger side and the middle bar for the driver side. wish I was still at Ft.Campbell Eddie it would be worth the drive to see you again. I went out there with Ed and you cut a rear corner section off a ww2 jeep for him. do you still have your GP?

Matt R

Eddie Holland · Unread post by **Eddie Holland** » April 16th, 2014, 10:57 pm

No I let the GP go. I had another Mighty Mite I sold last year and a M274A5 I sold. I bought an M151 and an M151A1 and 2 pickup and 16 ft trailer loads of parts to go with them. I still got a M151A2 and working on a 42 GPW. I hated to let the GP go but it was just too expensive. It was one of the earliest matching number GPS I have found in existence

I had just about tracked down all the parts and had the engine rebuilt. I got offered an amount I couldnt refuse.

42GPW · Unread post by **42GPW** » April 17th, 2014, 11:33 am

how much on the passenger side door frame and driverside middle support bar?

Matt R

Eddie Holland · Unread post by **Eddie Holland** » April 17th, 2014, 12:42 pm

what is the mid support frame? I will check see what I got this evening. I think I have a lot of door frames.

42GPW · Unread post by **42GPW** » April 17th, 2014, 12:52 pm

its in the middle. goes at an angle. and supports the door frame.
If I've completely confused you here is my cell (417) 316-1167
Matt R

Eddie Holland · Unread post by **Eddie Holland** » April 17th, 2014, 12:57 pm

send me an email to remind me. Im trying to figure out how to get email notifications from this site. My email is eddie_holland@bellsouth.net I know I have a lot of door frames. I was thinking maybe you were talking about the frame at the top on the other.

Unread post by **rickf** » April 17th, 2014, 3:42 pm

Eddie, where are you located?

42GPW · Unread post by **42GPW** » April 17th, 2014, 3:57 pm

near Ft.Campbell Ky.

Matt R

Unread post by **rickf** » April 17th, 2014, 8:50 pm

Going to Aberdeen?

salt6 · Unread post by **salt6** » May 3rd, 2014, 10:03 pm

Matt,

Did you ever find a frame? Going through my stuff today and found this right side. The front upright is for the left side. I need a right so I'm just going to weld two tubes on and call it good. The upper rod needs to be reriveted and you can fab a center rod if you can't find one.

Eddie Holland · Unread post by **Eddie Holland** » May 5th, 2014, 3:36 pm

Sorry some reason I am not getting email notifications. I am in Western Ky. Calvert City. I have a lot of door frames with skins on them.

WTB door frame

WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame

Re: WTB door frame