Looking For Some Stuff for M151A1
Moderators: rickf, raymond, Mr. Recovery
-
- Master Sergeant
- Posts: 377
- Joined: October 28th, 2009, 10:37 am
- Location: Ypsilanti Michigan
Re: Looking For Some Stuff for M151A1
I'm with ya! My brain left the building quite a while ago !!
1966 M151A1 ___All matching '44 M1 Garand
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ
-
- Master Sergeant
- Posts: 302
- Joined: November 25th, 2008, 10:54 pm
- Location: San Antonio, Texas
Re: Looking For Some Stuff for M151A1
Elvis.
If you are still looking for the screws for your distributor, (item 2 on your list), they are #10-32 x 5/8" Fillister Head Screws. Couldn't find any in local stores here, but found them on the Internet at http://www.americanintegratedsupply.com
And you need the #10 internal tooth washers for them also, to be correct.
They're cheap, 30 screws for $3.00, 150 washers for $3.00.
While you're at it, if you are going to do any carb repair, the Zenith carbs use the #10-24 x 5/8" Fillister Head Screws, 30 screws for $3.00, using the same #10 internal tooth washers. Might as well get them at the same time and combine shipping.
Hope this helps as I had a hard time matching screw sizes without new ones available.
Cal Fowler
If you are still looking for the screws for your distributor, (item 2 on your list), they are #10-32 x 5/8" Fillister Head Screws. Couldn't find any in local stores here, but found them on the Internet at http://www.americanintegratedsupply.com
And you need the #10 internal tooth washers for them also, to be correct.
They're cheap, 30 screws for $3.00, 150 washers for $3.00.
While you're at it, if you are going to do any carb repair, the Zenith carbs use the #10-24 x 5/8" Fillister Head Screws, 30 screws for $3.00, using the same #10 internal tooth washers. Might as well get them at the same time and combine shipping.
Hope this helps as I had a hard time matching screw sizes without new ones available.
Cal Fowler
Re: Looking For Some Stuff for M151A1
Apparently They did not pay their internet bill or they went out of business.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Re: Looking For Some Stuff for M151A1
1960 M151 Run #1
"There is one nut on a M151 that is very difficult to remove....." - K8icu
"She ain't a Cadillac and she ain't a Rolls, But there ain't nothin' wrong with the radio" - Aaron Tippin
"There is one nut on a M151 that is very difficult to remove....." - K8icu
"She ain't a Cadillac and she ain't a Rolls, But there ain't nothin' wrong with the radio" - Aaron Tippin
-
- Master Sergeant
- Posts: 302
- Joined: November 25th, 2008, 10:54 pm
- Location: San Antonio, Texas
Re: Looking For Some Stuff for M151A1
Yeah, That's them.Good stuff, cheap
Cal
Cal
-
- Master Sergeant
- Posts: 377
- Joined: October 28th, 2009, 10:37 am
- Location: Ypsilanti Michigan
Re: Looking For Some Stuff for M151A1
Thanks fowlercal - I'm going to sang a few extras just in case!!!
Have a good one!
Have a good one!
1966 M151A1 ___All matching '44 M1 Garand
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ
Re: Looking For Some Stuff for M151A1
And Elvis "Sang" a few extra's!
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone