Side Curtainz and Rod Assembly

cstaup · Unread post by **cstaup** » November 7th, 2012, 4:43 pm

Thanks, Dan. Well, here I go.

Fil Bonica · Unread post by **Fil Bonica** » November 7th, 2012, 10:39 pm

Have one set of rods for $ 25.00 plus shipping.

Fil Bonica

csmith · Unread post by **csmith** » November 8th, 2012, 6:34 pm

Set of Side Curtains for sale on EBay http://www.ebay.com/itm/M151-M151A1-M15 ... 56&vxp=mtr

Not mine....

ErEyal · Unread post by **ErEyal** » October 2nd, 2014, 4:48 pm

jumping an old post here so sorry for the trouble guys

i'm in the same deal now' i have the side curtains but not the rods, before i go and fabricate new ones, does any1 have a spare pair?

Thanks

Eyal

fowlercal · Unread post by **fowlercal** » October 3rd, 2014, 2:06 pm

ErEyal,

I got my NOS set of rods from Riv-Rad last month. They are $16.00 each, mine were still in the original govt wrapper. Check it out at muttparts.com Go to the M151 New Parts section, then scroll down to "Top Vertical Rod". They were shipped in a nice rigid cardboard container, no damage. Hard to beat NOS for 16 bucks and they are original.

Cal

ErEyal · Unread post by **ErEyal** » October 4th, 2014, 3:08 am

fowlercal wrote:ErEyal,

I got my NOS set of rods from Riv-Rad last month. They are $16.00 each, mine were still in the original govt wrapper. Check it out at muttparts.com Go to the M151 New Parts section, then scroll down to "Top Vertical Rod". They were shipped in a nice rigid cardboard container, no damage. Hard to beat NOS for 16 bucks and they are original.

Cal

Hey Cal,

found them right there, thanks for that.

did the fit good?

Eyal

fowlercal · Unread post by **fowlercal** » October 4th, 2014, 6:17 am

ErEyal.

The rods fit as they were designed. They slide in the slot on each side of the body, and the top of the rod fits into a hole in the top suport rod that goes to the windshield.

Cal

ErEyal · Unread post by **ErEyal** » October 14th, 2014, 4:43 am

Hi guys ,
After getting a shipping quote for more than 50 dollars i'm thinking of manufacturing the rods myself, doesn't look to complicated,
What taper you think i should use for the upped hole?
And what diameter of steel rod?

Thanks
Eyal

halftracknut · Unread post by **halftracknut** » October 14th, 2014, 7:42 am

If you want to go the easy route...I have seen a lot of these made from hardware store flat stock...all you do is drill one hole at top slide in and you are ready...

fowlercal · Unread post by **fowlercal** » October 16th, 2014, 1:19 am

ErEyl,

Where are you? $50.00 seems really high. My shipping was $16.00 to Texas. They weigh less than two pounds.

Cal

ErEyal · Unread post by **ErEyal** » October 16th, 2014, 6:01 am

Israel.....

Unread post by **rickf** » October 16th, 2014, 6:57 am

That would explain it.

Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly

Re: Side Curtainz and Rod Assembly