A1 & A2 Dash material thickness - input needed
Moderators: rickf, raymond, Mr. Recovery
-
- Brigadier General
- Posts: 2030
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
A1 & A2 Dash material thickness - input needed
I noticed that the material thickness of the NOS dash that I have and my '68 A1 dash are different. A1 is 18 ga and the NOS dash from Buddy is 20 ga. Anyone know if all A2 dashes are 20 ga? I'm guessing this was done to lower the cost at some point during manufacturing? Any input would be helpful as I'm getting ready to send to programming.
Guy
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
-
- Brigadier General
- Posts: 2506
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: A1 & A2 Dash material thickness - input needed
I'm sure those panels came from some of the last A2's built, perhaps some of the early A2's could be 18ga?????
Re: A1 & A2 Dash material thickness - input needed
I will check tomorrow. I did notice all of the cutouts on that dash panel that would not normally be on the earlier ones like the heater kit cut outs and some of the access holes. The one to the top right of the steering wheel has me guessing. The strange part is it is drilled for three circuit breakers, A2's only used two.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2030
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: A1 & A2 Dash material thickness - input needed
Did you have a chance to check Rick?
Guy
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: A1 & A2 Dash material thickness - input needed
Just posted on your other thread, I went out and got my micrometer and got sidetracked by a tree branch in the road and then the missus wanted something from the store. The mic is still sitting on the table. I will go out first thing in the morning and give you a call.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2030
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: A1 & A2 Dash material thickness - input needed
Thanks Rick.
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: A1 & A2 Dash material thickness - input needed
Looks like 18 Gauge on A1 and A2 to me.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2030
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: A1 & A2 Dash material thickness - input needed
18 ga it is.
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto