My M 151 A1 Restoration Project

A place to post pics and descriptions of ongoing restoration projects

Moderators: rickf, Mr. Recovery, raymond, moose53

Re: My M 151 A1 Restoration Project

Sponsor

Sponsor
 

Re: My M 151 A1 Restoration Project

Postby lpcoating » January 30th, 2017, 12:42 pm

Still trimming out floors on the passenger side. Used the seat to set the location of the front floor per earlier post. This thing drives me nuts. I was seeing some alignment issues and measurements that I did not like. So, I ran a string to verify that the seat was sitting "straight" in the truck. Looks pretty good so the location and position of the seat support is set. Notice the gap on the inside of the floor board where it meets the toe board. I was seeing this on the back side and as the outside edge sets this position I'll modify the toe board to fit up better in this area. Nothing is straight on these things! I'm sure the X cut didn't help. I'll deal with...

Image
Image
Image
Image

Cutting for the panel offset:

Image
Image

Using clamps, 18ga and a hammer to make offset:

Image
Image
Image
Image
Image

This way the side sits flush on the seam:

Image

Notice the gap in the corner:

Image
Image
Image
Image

Guy
M151 Body Panels - http://www.m151bodypanels.com/

'68 A1 - Under full resto
lpcoating
Major
Major
 
4 years of membership4 years of membership4 years of membership4 years of membership
 
Posts: 1197
Joined: February 19th, 2013, 10:38 pm
Location: Mansfield, PA

Re: My M 151 A1 Restoration Project

Postby lpcoating » January 30th, 2017, 3:43 pm

Now that I look at these pictures some more and then the picture of the string line on the rear fender top it makes sense as to why the floor is meeting up with the toe board that way. Guess I need to lower my tolerance standards when it comes to fixing an "X" cut.

Guy
M151 Body Panels - http://www.m151bodypanels.com/

'68 A1 - Under full resto
lpcoating
Major
Major
 
4 years of membership4 years of membership4 years of membership4 years of membership
 
Posts: 1197
Joined: February 19th, 2013, 10:38 pm
Location: Mansfield, PA

Re: My M 151 A1 Restoration Project

Postby m3a1 » January 31st, 2017, 10:43 am

Yup. It's easy to get derailed by the details. Your circumstance reminds me of an experience with a range instructor I once had. I was getting all wrapped around the axle about some minor detail and he said, "Just shoot the damned target!" So, I did.
m3a1
Command Sergeant Major
Command Sergeant Major
 
2 years of membership2 years of membership
 
Posts: 621
Joined: August 7th, 2014, 5:36 pm

Re: My M 151 A1 Restoration Project

Postby Hambone » January 31st, 2017, 7:32 pm

There goes your side panel, Rick, tack it up , Guy, it looks good. :lol: :lol: :lol:
Hambone
Captain
Captain
 
6 years of membership6 years of membership6 years of membership6 years of membership6 years of membership6 years of membership
 
Posts: 1083
Joined: September 30th, 2010, 11:19 pm
Location: El Dorado, Arkansas

Re: My M 151 A1 Restoration Project

Postby rickf » February 1st, 2017, 2:42 pm

:lol: :lol: :lol: :lol: :lol: Yea, lower my tolerances, Right. That would be like asking any redblooded American male to dump cold beer down the sink and put ketchup on steak! AIN'T GONNA HAPPEN!
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
rickf
General
General
 
9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership
 
Posts: 13418
Joined: November 26th, 2007, 12:28 pm
Location: Pemberton, NJ.

Re: My M 151 A1 Restoration Project

Postby lpcoating » March 20th, 2017, 5:44 am

Made some more progress on the passenger side front floor over the weekend. I painted the seam areas with POR yesterday and it's now ready to be welded in place.

Image
Image
Image
Image
Image
Image
Image
Image


Guy
M151 Body Panels - http://www.m151bodypanels.com/

'68 A1 - Under full resto
lpcoating
Major
Major
 
4 years of membership4 years of membership4 years of membership4 years of membership
 
Posts: 1197
Joined: February 19th, 2013, 10:38 pm
Location: Mansfield, PA

Re: My M 151 A1 Restoration Project

Postby rickf » March 20th, 2017, 8:37 am

Damn it must be nice to have access to an unlimited supply of sheet metal, even if you have to pay for it. I have to drive a LONG ways to get it.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
rickf
General
General
 
9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership
 
Posts: 13418
Joined: November 26th, 2007, 12:28 pm
Location: Pemberton, NJ.

Re: My M 151 A1 Restoration Project

Postby m3a1 » March 20th, 2017, 9:39 am

There must be a law in Jersey that you can never have enough of anything.....metal suppliers.....shells in yer shotgun.....etc. :lol: :lol: :lol:
m3a1
Command Sergeant Major
Command Sergeant Major
 
2 years of membership2 years of membership
 
Posts: 621
Joined: August 7th, 2014, 5:36 pm

Re: My M 151 A1 Restoration Project

Postby rickf » March 20th, 2017, 1:38 pm

We have metal suppliers, just not near me. The one I deal with is huge so when I go there I am squeezed in with all the big trucks in my little dually. They are picking up steel by the multiple tons and I am picking up a ton at the most! Needless to say I do not have top priority but I do get pretty good service. Guy may know of Fazzio's steel.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
rickf
General
General
 
9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership
 
Posts: 13418
Joined: November 26th, 2007, 12:28 pm
Location: Pemberton, NJ.

Previous

Return to Restoration Projects

Who is online

Users browsing this forum: No registered users and 1 guest

Customization by G838.org