pilot bearing

This is the place to get help with technical matters concerning your M151 jeep

Moderators: rickf, raymond, Mr. Recovery

Post Reply
Mark
Brigadier General
Brigadier General
Posts: 2085
Joined: September 19th, 2009, 11:33 pm
Location: South Dakota

pilot bearing

Unread post by Mark » April 24th, 2018, 10:51 am

I am trying to correct my memory, the 151 had a pilot bushing? the later mutts had a pilot bearing?
mark


1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416

User avatar
rickf
General
General
Posts: 19738
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: pilot bearing

Unread post by rickf » April 24th, 2018, 4:56 pm

I never really thought about that, that is a question for Ken. As far as I know the crankshaft hole is the same so even if the old one used a bushing you could put in the later bearing.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

Fil Bonica
Brigadier General
Brigadier General
Posts: 2607
Joined: December 9th, 2007, 10:49 am
Location: ~ Heaven ~

Re: pilot bearing

Unread post by Fil Bonica » April 24th, 2018, 5:41 pm

There is a bushing for the starter shaft in the bell housing but not it the flywheel.
Fir what it’s worth.

Fil Bonica
K1ABW

halftracknut
Brigadier General
Brigadier General
Posts: 2064
Joined: December 11th, 2007, 2:28 pm

Re: pilot bearing

Unread post by halftracknut » April 24th, 2018, 6:12 pm

Bronze oil lite bearing (really a bushing) in the flywheel......main shat in tranny goes in it....
slowest mutt east of the missippi..

User avatar
rickf
General
General
Posts: 19738
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: pilot bearing

Unread post by rickf » April 24th, 2018, 6:49 pm

halftracknut wrote:Bronze oil lite bearing (really a bushing) in the flywheel......main shat in tranny goes in it....
Bearing as in ball bearing, caged. The main shat goes into that.

https://www.ebay.com/i/172710386101?chn=ps
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

acudanut

Re: pilot bearing

Unread post by acudanut » April 26th, 2018, 1:45 am

Fil Bonica wrote:There is a bushing for the starter shaft in the bell housing but not it the flywheel.
Fir what it’s worth.

Fil Bonica
I believe there is a bearing in the flywheel (rear bearing, back of engine.)


User avatar
rickf
General
General
Posts: 19738
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: pilot bearing

Unread post by rickf » May 2nd, 2018, 8:42 pm

That is the very same link I put up two posts up.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

acudanut

Re: pilot bearing

Unread post by acudanut » May 2nd, 2018, 9:55 pm

Great, we are on the same page.

User avatar
rickf
General
General
Posts: 19738
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: pilot bearing

Unread post by rickf » May 3rd, 2018, 7:56 am

:lol: :lol:
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

Post Reply