M416 Wiring Question

need more space? add a M416 trailer! and discuss it here.

Moderators: rickf, raymond, Mr. Recovery

Post Reply
vtdeucedriver
Master Sergeant
Master Sergeant
Posts: 399
Joined: March 9th, 2008, 8:05 pm

M416 Wiring Question

Unread post by vtdeucedriver » May 17th, 2010, 8:58 pm

Hey all, I took the wiring off and I cant remember if the wire runs up over between the frame and the tub at the front where it comes from the intervehicle cable or does it go under the frame and into the holes down the side. I would think it goes above the frame and scoot between the tub and the frame.
Jeff
Army Transportation Assoc Vietnam, Associate Member
Vietnam Veterans Assoc, Associate Member
Green Mountain Military Vehicle Club
1968 M52A2
1968 M54A2
1968 M151A1
1964 M151A1
1953 M62
1951 M37
" I am deuceless" Sold them all.

User avatar
Mr. Recovery
Brigadier General
Brigadier General
Posts: 2895
Joined: December 5th, 2007, 9:03 pm
Location: New Port Richey, Fl.
Contact:

Re: M416 Wiring Question

Unread post by Mr. Recovery » May 17th, 2010, 9:34 pm

Hope this helps! :)

Image

Image
1960 M151 Run 1
1963 M151 Willys DoD 10-63 in Baltimore
1989 Alley Cat. "work in Progress"
NRA Life Member
American Legion Post 275 Fl
US Army 6 years 2nd Armored Cavalry Bindlach Germany
Colorado Army Nat. Guard 5 years
Md Air Guard 15 years active duty on C-130's

vtdeucedriver
Master Sergeant
Master Sergeant
Posts: 399
Joined: March 9th, 2008, 8:05 pm

Re: M416 Wiring Question

Unread post by vtdeucedriver » May 18th, 2010, 7:50 am

LOL, nope not really!!! I cant see my area of concern. If you look as it goes foreward through the last horizontal support (in the flipped picture). It goes up the frame to the pintal, it then needs to go inside that frame. When it crosses that frame, is it between the frame and the tub???? I cant remember how mine was. If anyone has a M416, just take a peak and tell me. I might just remove the bolts from the tub again and sneak it between there as I would think that it would but I am not sure.
Jeff
Army Transportation Assoc Vietnam, Associate Member
Vietnam Veterans Assoc, Associate Member
Green Mountain Military Vehicle Club
1968 M52A2
1968 M54A2
1968 M151A1
1964 M151A1
1953 M62
1951 M37
" I am deuceless" Sold them all.

User avatar
rickf
General
General
Posts: 19762
Joined: November 26th, 2007, 1:28 pm
Location: Pemberton, NJ.

Re: M416 Wiring Question

Unread post by rickf » May 18th, 2010, 8:30 am

I know on mine the tub is tight against the frame all along the outer edges and also tight against the lip on the front. I would be pretty sure it goes under at that point. If you have to loosen a bolt to get it in then that is not the right route. The harness will come out without removing any bodywork.

Rick
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone

User avatar
Mr. Recovery
Brigadier General
Brigadier General
Posts: 2895
Joined: December 5th, 2007, 9:03 pm
Location: New Port Richey, Fl.
Contact:

Re: M416 Wiring Question

Unread post by Mr. Recovery » May 18th, 2010, 9:52 pm

:) The wires run up and over the frame just behind the parking brake .

Image

http://s195.photobucket.com/albums/z96/ ... =001-6.jpg

Image
1960 M151 Run 1
1963 M151 Willys DoD 10-63 in Baltimore
1989 Alley Cat. "work in Progress"
NRA Life Member
American Legion Post 275 Fl
US Army 6 years 2nd Armored Cavalry Bindlach Germany
Colorado Army Nat. Guard 5 years
Md Air Guard 15 years active duty on C-130's

User avatar
Rainman
Brigadier General
Brigadier General
Posts: 2398
Joined: November 28th, 2007, 12:32 am

Re: M416 Wiring Question

Unread post by Rainman » May 19th, 2010, 3:16 pm

Not being on my own computer at the time, I can't really see the pictures in the detail needed to view the area in question, but I'm going to say UNDER. If I'm picturing the area in question properly, it is not impinged by the tub, and looks somewhat vulnerable, and under the frame at the front of the tub.
Rainman
M151 World Land Speed Record Holder

User avatar
Mr. Recovery
Brigadier General
Brigadier General
Posts: 2895
Joined: December 5th, 2007, 9:03 pm
Location: New Port Richey, Fl.
Contact:

Re: M416 Wiring Question

Unread post by Mr. Recovery » May 21st, 2010, 5:50 pm

I went out back into the "SWAMP" :roll: and uncovered two of the trailers to have a look, they both run under the drawbar then to the frame,

trailer#1
Image

Image

Image

trailer#2
Image

Image

The page I posted earlier was from a trailer TM dated Oct. 1970, perhaps it was changed at a later date. :)

Image
1960 M151 Run 1
1963 M151 Willys DoD 10-63 in Baltimore
1989 Alley Cat. "work in Progress"
NRA Life Member
American Legion Post 275 Fl
US Army 6 years 2nd Armored Cavalry Bindlach Germany
Colorado Army Nat. Guard 5 years
Md Air Guard 15 years active duty on C-130's

User avatar
Rainman
Brigadier General
Brigadier General
Posts: 2398
Joined: November 28th, 2007, 12:32 am

Re: M416 Wiring Question

Unread post by Rainman » May 25th, 2010, 7:17 pm

Thanks Dan,
That's what I attempted to describe.
Sunman 8)
M151 World Land Speed Record Holder

User avatar
mrdibbles
Colonel
Colonel
Posts: 1720
Joined: November 25th, 2007, 9:51 pm

Re: M416 Wiring Question

Unread post by mrdibbles » May 25th, 2010, 9:21 pm

Is that Mud-Dauber nest mil-spec?
1992 Mercedes-Benz 250GD Wolf - Former German Army
St. Augustine, Florida

Francis Marion
2nd Lieutenant
2nd Lieutenant
Posts: 877
Joined: June 22nd, 2009, 2:29 pm
Location: Taylorsville, UT
Contact:

Re: M416 Wiring Question

Unread post by Francis Marion » May 25th, 2010, 11:58 pm

mrdibbles wrote:Is that Mud-Dauber nest mil-spec?
It must be, mine came with one.
1968 M151A1
1967 M416

Post Reply