Battery Distribution Upgrade Directions
Moderators: rickf, raymond, Mr. Recovery
Battery Distribution Upgrade Directions
I'm picking back up on installing this upgrade, but if course the directions sheet is now missing. Can someone supply a copy?
Jim Peterson
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!
-
- Brigadier General
- Posts: 2607
- Joined: December 9th, 2007, 10:49 am
- Location: ~ Heaven ~
Re: Battery Distribution Upgrade Directions
Find # 21 in the passenger rear harness.
Break open the connector.
Take the jumper and connect to each end.
The loose wire is then connected to the license plate light.
If you need the assembly I can supply an equivalent with a wire long enough to reach the license plate frame for $15.00 shipped.
Fil Bonica
Break open the connector.
Take the jumper and connect to each end.
The loose wire is then connected to the license plate light.
If you need the assembly I can supply an equivalent with a wire long enough to reach the license plate frame for $15.00 shipped.
Fil Bonica
K1ABW
Re: Battery Distribution Upgrade Directions
Thanks Fil, but what I'm looking for is (properly) called Battery Junction Terminal Kit, part# 12302545. There is a printed schematic that comes with the kit. This schematic is what I'm hoping someone can send me a copy of.
Jim Peterson
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!
-
- Brigadier General
- Posts: 2607
- Joined: December 9th, 2007, 10:49 am
- Location: ~ Heaven ~
Re: Battery Distribution Upgrade Directions
Misunderstood :was relating to a prior post
Every time I used one of those kits I immediately threw the directions away when finished.
In fact the only parts that I used were the jumper and the big electrical stud that mounts between the two batteries.
I then reconnected the battery cable and the jumper.
Any accessory wiring can be added there.
Never used the rubber battery terminal boots and stiffeners because they were too awkward
Always liked the old style boots that surrounded the terminal.
Hope this helps and doesnt confuse the issue more.
Fil Bonica
Every time I used one of those kits I immediately threw the directions away when finished.
In fact the only parts that I used were the jumper and the big electrical stud that mounts between the two batteries.
I then reconnected the battery cable and the jumper.
Any accessory wiring can be added there.
Never used the rubber battery terminal boots and stiffeners because they were too awkward
Always liked the old style boots that surrounded the terminal.
Hope this helps and doesnt confuse the issue more.
Fil Bonica
K1ABW
-
- Brigadier General
- Posts: 2607
- Joined: December 9th, 2007, 10:49 am
- Location: ~ Heaven ~
Re: Battery Distribution Upgrade Directions
If you refer to the -20-1-1 pgs5-60.2 thru 5-65
Change 2
You will find some good info on how the parts are installed.
Its not the original instructions but it is a good alternate.
Fil Bonica
Change 2
You will find some good info on how the parts are installed.
Its not the original instructions but it is a good alternate.
Fil Bonica
K1ABW
Re: Battery Distribution Upgrade Directions
Hope this helps
ugh..I see it is resizing it and I made it a large file so you can read it.
try the link also
https://ibb.co/h0jpKz
Re: Battery Distribution Upgrade Directions
Thanks to all for the assist!
Jim Peterson
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!
SGM, 31B Retired 2015
1961 M151 -Sold
1974 M151A2, Working It!