Winch ID

discuss various tools and accessories for your mutts here.

Moderators: rickf, Mr. Recovery, raymond, moose53

Winch ID

Sponsor

Sponsor
 

Winch ID

Postby salt6 » August 13th, 2009, 7:44 pm

This was on the front of my MUTT. I took it off because it was tearing the front bumper mounts out. Anyone got any idea what it is? The guy I got it from was an active duty marine and had installed it on the front bumper.

Image

Image

Image

Image

Image

Did I mention it's HEAVY.
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf."

George Orwell
-------------------------------------
"I once was one of those men."

salt6

http://www.mg42.us
User avatar
salt6
Sergeant Major of the "G"
Sergeant Major of the "G"
 
9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership
 
Posts: 792
Joined: April 5th, 2008, 11:18 pm
Location: NE Okla

Re: Winch ID

Postby moose53 » August 14th, 2009, 1:36 am

looks to me kinda like the ones used on humvees, but I'm not sure about that.

Jim
Zigzag50, Northeast51, KC2QDZ
MVPA # 30032 G838.org

--------------------------------------
1971 G838-M151A2 1966 G857-M416
1968 G748-M101A1 1976 G748-M116A1
1990 MEP-701A

--------------------------------------
Real jeeps have horizontal grille slots
User avatar
moose53
Site Admin
Site Admin
 
10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership
 
Posts: 2640
Joined: November 25th, 2007, 7:44 pm
Location: Moscow PA

Re: Winch ID

Postby rickf » August 14th, 2009, 5:07 am

Looks like a Warn 10,000 lb.. Is it electric or hydraulic? If electric is it 24 volt? I notice you have the mutt on the trailer backwards??? That is putting WAY to much weight bias towards the back of the trailer, You need at least 7-10% of the total load on the tongue for stability. Is the left front suspension bent? Even pulled down tight it should not be bent like that.

Rick
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
rickf
General
General
 
10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership10 years of membership
 
Posts: 14525
Joined: November 26th, 2007, 12:28 pm
Location: Pemberton, NJ.

Re: Winch ID

Postby salt6 » August 14th, 2009, 6:59 pm

It's 24 volts.

Photo is about two years old now, and yes I figured that out on the drive home. :D

Prepping for a total respray. It has the wrong springs on the front. Got replacements from HK awhile back just haven't had time to put them on.
"People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf."

George Orwell
-------------------------------------
"I once was one of those men."

salt6

http://www.mg42.us
User avatar
salt6
Sergeant Major of the "G"
Sergeant Major of the "G"
 
9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership9 years of membership
 
Posts: 792
Joined: April 5th, 2008, 11:18 pm
Location: NE Okla


Return to Tools and Accessories

Who is online

Users browsing this forum: No registered users and 0 guests

Customization by G838.org
cron