Body working !! Need mesures
Moderators: rickf, raymond, Mr. Recovery
Body working !! Need mesures
Hi, i ve been working on the back seat floor. I removed the old/flat/ not original piece and made a new one! But i need some accurate mesures. The 5 "lines" ( i dont know the exact word for them) resulted to be too wide i think. Can anyone send me length of the top side, the height, and the length of the lower part?? Also the distance ( from center of each "line") beetween them. Heres a pic of my first attempt to make it. !! Thanks and keep in touch
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
Re: Body working !! Need mesures
Wow, Nice work. I am sure you will get a reply from Lpcoating. He is producing the rear floors for the 151 here in the states. I am guessing it would be too expensive to ship one to you but he might give you the measurements you are looking for.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Body working !! Need mesures
Thanks, nice work but not accurate! Here is reaaaally expensive to be shipped. For a vinyl top i bougjt in the US (80 dollars) it finally cost over 400 dollars !!
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
Re: Body working !! Need mesures
OUCH! I can measure the rust bucket I have for you but it will not be until Saturday. It is dark when I get home from work during the week now, I hate winter! The measurements will be in inches, I do not have a metric tape or ruler.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Body working !! Need mesures
That will be great!!! Thanks! For convertion is google jjaja
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
-
- Brigadier General
- Posts: 2027
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Body working !! Need mesures
The rear floor rib is the same as the trans cover and front floor ribs. If you can't use them as a reference I have the info from the tool that we purchased.
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Body working !! Need mesures
I m makeing all new! Everything was bad, twisted, unoriginal...etc. Any information is very thanked and welcome!!!
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
-
- Brigadier General
- Posts: 2027
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Body working !! Need mesures
Give me a day or two and I'll get the dimensions.
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Body working !! Need mesures
Great! Thanks
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
-
- Brigadier General
- Posts: 2027
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Body working !! Need mesures
These dimensions (in inches) are from the bend center lines:
The base of the rib is 1.126" wide
The width at the top of the rib (from the inside) is .570"
The height of the rib from the top of the rib to the top of the floor is .170"
Bend radius (our tooling) is .085"
The angle of the bends are 49 deg.
Original floor thickness is 18 ga.
Hope this makes sense...
For your reference:
http://www.m151bodypanels.com/products-rearfloor.htm
Guy
The base of the rib is 1.126" wide
The width at the top of the rib (from the inside) is .570"
The height of the rib from the top of the rib to the top of the floor is .170"
Bend radius (our tooling) is .085"
The angle of the bends are 49 deg.
Original floor thickness is 18 ga.
Hope this makes sense...
For your reference:
http://www.m151bodypanels.com/products-rearfloor.htm
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Body working !! Need mesures
Thats reaaaally good information thanks for all of you for the help, ill try to reproduce that piece this week and upload photos!!
Alvaro Martinez from Uruguay
Alvaro Martinez from Uruguay
Re: Body working !! Need mesures
I didn't post anything because I could not have come close to that detail. That is why I was hoping Guy would chime in with that.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Body working !! Need mesures
This week i cutted off the back floor and made the new one with the help you all gave me. Heres a photo i hope you can see what was under the floor!!! Y need to re-make everything under there!!!
Couple of days and post the new floor.
Alvaro Martinez from Uruguay
Couple of days and post the new floor.
Alvaro Martinez from Uruguay