My M 151 A1 Restoration Project
Moderators: rickf, raymond, Mr. Recovery
Re: My M 151 A1 Restoration Project
What are you planning to do with the cut lip at the top of the fenderwell under the new fender top? That is a bare edge that will be pone to rust and it is going to be hard to seal that area since it is open to the tire.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2039
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: My M 151 A1 Restoration Project
It will be sprayed with primer before installing the fender and maybe I'll use some type of sealer on the inside only. I thought about the rust issues but also thought that basically every seam on the truck is that way so 2 more wouldn't hurt!rickf wrote:What are you planning to do with the cut lip at the top of the fenderwell under the new fender top? That is a bare edge that will be pone to rust and it is going to be hard to seal that area since it is open to the tire.
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: My M 151 A1 Restoration Project
I know how you work (so there's really little chance of trouble) but have you laid the hood on to see how its lower edges will be in relation to your fender tops?
I'm excited. Now it's really starting to look like something! Please take a step back and take a picture of the whole thing as it sits now.
Cheers,
TJ
I'm excited. Now it's really starting to look like something! Please take a step back and take a picture of the whole thing as it sits now.
Cheers,
TJ
-
- Brigadier General
- Posts: 2039
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: My M 151 A1 Restoration Project
Should be the same as stock as the rear height is set by the original tab on the fire wall and the front height is set by what is left of the original front fender. I will put the hood on and eye ball it just because.m3a1 wrote:I know how you work (so there's really little chance of trouble) but have you laid the hood on to see how its lower edges will be in relation to your fender tops?
I'm excited. Now it's really starting to look like something! Please take a step back and take a picture of the whole thing as it sits now.
Cheers,
TJ
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: My M 151 A1 Restoration Project
I'm sure with you at the helm there is very little chance for error. I just keep thinking of that poor fellow who recently had all that work accomplished and then found the hood was short (or more likely, his fenders were too low).
Re: My M 151 A1 Restoration Project
Never did hear the result on that did we?
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2039
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: My M 151 A1 Restoration Project
Driver side fender top is now ready to be installed. Has a little bit of a gap at the bottom of the front edge but will not be a problem as I'll use an aluminum backer. I like to have about a .030" - .040" gap when doing a butt weld as the weld will be ground flush and I want full penetration. Also took a picture of the primer I'm using between panels. I take a scribe and scratch off the primer in the plug weld area it works very well.
Guy
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: My M 151 A1 Restoration Project
No we never did hear how that played out. I see one of the reasons why you're not terribly concerned about hood gap, given that you still have the original inner fenders in place.
TJ
TJ
Re: My M 151 A1 Restoration Project
Are you welding through that or cleaning off each spot?
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2039
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: My M 151 A1 Restoration Project
I scratch off the primer for each plug weld and also use a round file for the inside edge of the slots to remove the primer. Do not have any issue welding by doing this.rickf wrote:Are you welding through that or cleaning off each spot?
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
- Vzike
- Sergeant Major of the "G"
- Posts: 729
- Joined: December 27th, 2013, 4:05 pm
- Location: Jupiter, Florida
Re: My M 151 A1 Restoration Project
I've got an ongoing test.... two pieces of sheet metal, painted with POR15 top coat, drilled and the primer scratched off.
The button welds are solid.... let's see how they hold up next to the building with the salt spray from the ocean. I'm 300 yards from the ocean with regular/steady onshore breezes.
The POR has held up very nicely to scraps I've put out there in the past.
The button welds are solid.... let's see how they hold up next to the building with the salt spray from the ocean. I'm 300 yards from the ocean with regular/steady onshore breezes.
The POR has held up very nicely to scraps I've put out there in the past.
-
- Brigadier General
- Posts: 2039
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: My M 151 A1 Restoration Project
Driver side front fender is installed. Need to do some grinding and blending but that's the easy part. Next will be removing the driver side seat support as the one pictured was installed long before we made replacement parts. After that I need to build a driver side toe board and then the dash.
Pictures of the project as it sits today:
Guy
Pictures of the project as it sits today:
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: My M 151 A1 Restoration Project
Looks like you are getting real close to needing those complete side panels!
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
Re: My M 151 A1 Restoration Project
a nice view on how little else Guy will need to make a full new body
Horst
1972 USMC M151A2 w/ROPS (ex Barstow) and M416
1962 M201 and trailer
1966 GTO,1982 E350 Skoolie, 1987 SJ413, 1987 911
Gone: 2xM35A2c, Unimog 404S, Hanomag AL28, DKW Munga
1972 USMC M151A2 w/ROPS (ex Barstow) and M416
1962 M201 and trailer
1966 GTO,1982 E350 Skoolie, 1987 SJ413, 1987 911
Gone: 2xM35A2c, Unimog 404S, Hanomag AL28, DKW Munga
Re: My M 151 A1 Restoration Project
Obviously, he's cleaned up his work space. See those anchors in the floor? That's how he keeps his monster chained down when he's not in the room!