M151A2 Oil Pan Gasket
Moderators: rickf, raymond, Mr. Recovery
-
- Private First Class
- Posts: 23
- Joined: March 17th, 2015, 12:42 am
- Location: Colorado Springs, CO
M151A2 Oil Pan Gasket
Anyone know if there's an aftermarket cork oil pan gasket out there? I bought an NOS one from AJP but it arrived broken. This is the second one that I obtained (first one dated 3/62 & second dated 8/62) both were so brittle that shipping broke them. The front and rear rubber was fine in both though. Just about to finish up engine but need a gasket.
Fast Eddie
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)
Re: M151A2 Oil Pan Gasket
Could make your own. Use the bad ones as a template. AutoZone and similar stores sell rolls of the stuff which will be a hell of a lot newer . Good utility knife and a hole punch and you're in business.
1960 M151 Run #1
"There is one nut on a M151 that is very difficult to remove....." - K8icu
"She ain't a Cadillac and she ain't a Rolls, But there ain't nothin' wrong with the radio" - Aaron Tippin
"There is one nut on a M151 that is very difficult to remove....." - K8icu
"She ain't a Cadillac and she ain't a Rolls, But there ain't nothin' wrong with the radio" - Aaron Tippin
Re: M151A2 Oil Pan Gasket
Check with places like Front line and Red River, There should be gaskets out there from at least the 80's. If not, like was said, get material and make your own. I would use the oil pan itself for the template to get the outside outline and hole position and then use one of the other gaskets for the width to the inside line. This way you KNOW the holes are in the right place.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Private First Class
- Posts: 23
- Joined: March 17th, 2015, 12:42 am
- Location: Colorado Springs, CO
Re: M151A2 Oil Pan Gasket
Thanks for the suggestions Surveyor and Rick. I believe I'll go down to AutoZone or O'Reilly's today and get some material and make my own. Will also post some pics soon of the restoration progress. Thanks again, FE
Fast Eddie
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)
- raymond
- Major General
- Posts: 3428
- Joined: November 26th, 2007, 8:29 pm
- Location: God's country, Clarksville Mo.
Re: M151A2 Oil Pan Gasket
Old spent rifle and pistol brass make good makeshift hole punches. But you only get a couple holes per each before the brass deforms.
Raymond
"On the day when crime puts on the apparel of innocence, through a curious reversal peculiar to our age, it is innocence that is called on to justify itself." Albert Camus
"On the day when crime puts on the apparel of innocence, through a curious reversal peculiar to our age, it is innocence that is called on to justify itself." Albert Camus
-
- Private First Class
- Posts: 23
- Joined: March 17th, 2015, 12:42 am
- Location: Colorado Springs, CO
Re: M151A2 Oil Pan Gasket
Great idea, I was going to buy a school punch to cut the holes with but have quite a bit of used brass lying around. Will grind it down sharp with a dremel, should work great.
Fast Eddie
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)
USN 1981-2006
W5HAV
1970? M151A2
1970 M151A2 purchased in Panama (Fort Clayton, CZ) circa 1972, but unfortunately at the time could not ship to the States. (SOLD)