Your right Rick,just lucked up on them, they were posted on the 503, I just happened to be on there when he posted them, only 50 miles away, going to put them under the shed with my other junk, my wife doesn't call me Fred G. Sanford for nothing, I guess he sold his treasures though.rickf wrote:Man, those things are like gold hens teeth!!! Put them on the 503 and you will get real good money for them. That will pay for even more junk!!
Generic jeep
Moderators: rickf, raymond, Mr. Recovery
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Getting back on the Titan jeep, cutting the floors out with .040 cutoff wheels, going to use my cutouts to shear my new panels, that should give me the right gap to weld back in.
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Picked up a nice MBT trailer today, these are getting hard to find.
Re: Generic jeep
Got a case of the shakes there dude? I know I am getting old but my aren't quite that fuzzy!
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Yup, went and got it early this morning, haven't had my drink yet , I was nervous all morning thinking they were going to check the value and try to give my money back, too bad they didn't know what they had, too late now.
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Just had my glass installed, he installed this type of seal, said I could replace the glass with ease in the future, $100 total.
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
I have a temp gauge question, the one on the left came out of the Ally Cat, the one on the right is an NOS I want to replace it with, is it a direct replacement or have I read the gauge has to match the sender? Thanks Hambone
Re: Generic jeep
Has to match the sender, now the question is, did it work correctly in the Ally Cat? It will not harm anything to plug it in and try it, if you know the thermostat is good then it will be obvious if the sender is right or wrong. You don't even have to install the gauge, plug the two wires in and then run a ground wire with alligator clips from the gauge housing to a good ground.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Thanks Rick, I going to install and keep my fingers crossed.
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Finally took the time to build my rotisserie, too much dust in the shop from sanding and grinding, built it so I could hook up to my tractor and pull in and out of shop.
Re: Generic jeep
I am not seeing any rotisserie action on the tractor end? I assume there is more to it? Good idea with the big tires, got to look into that one.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Both ends are the same, it's 2" inside 21/2" pipe, I put holes in pipe in 90 degree increments so I could pin it when I spin it, I think I will weld a nut on the 3" and insert a bolt so I can tighten it down on any angle.
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
Got my M416 sanded and painted, used truck bed liner in the floor, still need to remove the wheels for paint.
Re: Generic jeep
C'mon man! At least straighten the landing leg!
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2528
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
OK!!