Search found 873 matches

by svramselaar
February 20th, 2020, 8:31 am
Forum: Technical Discussion
Topic: cam gear
Replies: 0
Views: 55

cam gear

hi there where mabey a 100 pertinax cam gears at my block sits a steel one at the camshaft ??? was this steel one a modification ??? both std crankshaft bearing sets € 80,- i got a engine gasket set €25,- gearbox gasket set € 10,- bellhousing gasket set € 5,- clutch pressure bearing €8,- oilfilter €...
by svramselaar
February 17th, 2020, 12:40 pm
Forum: Technical Discussion
Topic: Rear turn signals.......Modifications
Replies: 13
Views: 1546

Re: Rear turn signals.......Modifications

hi all the original wire`s must leave as they sits only you take a new wire from it wire 22 is at the switch D this is the stop wire from the light switch wire 460 is at the switch A this is the R turn wire to the front light wire 461 is at the switch B this is the L turn wire to the front light geo...
by svramselaar
February 17th, 2020, 6:08 am
Forum: Technical Discussion
Topic: Rear turn signals.......Modifications
Replies: 13
Views: 1546

Re: Rear turn signals.......Modifications

hi you have a other problem you want to work the MUTT with combined stop direction lights and the trailer with seperated lights the easyest way at the directional switch are the wire`s 22 =/ 460=/461 make a T connection from all three wire`s take them to the receptacle assy the new wire 22 is the st...
by svramselaar
February 17th, 2020, 5:42 am
Forum: Technical Discussion
Topic: engine
Replies: 6
Views: 199

Re: engine

hi

thanks for the answer

after my block was at my friend i saw the tube`s at the parts manual
now i know they wil stay in place at the block

george
by svramselaar
February 16th, 2020, 7:24 am
Forum: M151 mods
Topic: A2 Wiper Motor Power in A1 Mutt
Replies: 11
Views: 1412

Re: A2 Wiper Motor Power in A1 Mutt

hi

normaly the A2 wiper get power from wire 27
this is the wire at dasch for the meters
there is also a fuse at this wire both sides no27

george
by svramselaar
February 16th, 2020, 7:16 am
Forum: Technical Discussion
Topic: engine
Replies: 6
Views: 199

Re: engine

hi

thanks i think
tube 8 is at the block for the oilpressure tube to the rockerarms
tube 7 is the return oil tube to the block it go`s the return oil over the ignition drive

the place of the seals is normal only are there four or two

george
by svramselaar
February 15th, 2020, 6:26 am
Forum: Technical Discussion
Topic: engine
Replies: 6
Views: 199

engine

hi finaly i have my engine apart cranckshaft is as new at the bearings STD all bearings the cylinders are a bit worn out STD there are groove`s inside the block is at my friend for the 2`oversize bore i have two qwestions at the block are two tube`s at the drawing no 7 and 8 are they press in the bl...
by svramselaar
February 6th, 2020, 10:43 am
Forum: General Discussion
Topic: Magnetic Drill Press
Replies: 39
Views: 710

Re: Magnetic Drill Press

hi

i used them several time`s to drill holes at truck chassis
if it has a electric magnet we alwais take a cable to hold the drill in place for safety
if the power is from your electric system the magnet has no power and the drill wil fall to the ground :oops:

george
by svramselaar
January 11th, 2020, 8:19 am
Forum: M151 Wanted
Topic: WTB A2 Windshield Wiper Pin
Replies: 1
Views: 128

Re: WTB A2 Windshield Wiper Pin

by svramselaar
January 8th, 2020, 5:45 am
Forum: Technical Discussion
Topic: Source for 24 volts?
Replies: 13
Views: 424

Re: Source for 24 volts?

hi

aboud the 12 v from one battry
i have seen the problems at the 40 years i am a car electrician
mark has this item as replay above my replay

george
by svramselaar
January 7th, 2020, 6:11 am
Forum: Technical Discussion
Topic: Source for 24 volts?
Replies: 13
Views: 424

Re: Source for 24 volts?

hi for 12v use alwais a dc-dc converter 24-12v if you take from one battery the power it will cost a battery if the total voltage is 26 volt (full battery`s ) at the midle 13 volt`s if you use a radio +/- 3-6 amps form one battery the voltage go more down as at the set example battery one 11 volt se...
by svramselaar
December 26th, 2019, 6:22 am
Forum: Technical Discussion
Topic: new engine problems
Replies: 40
Views: 1479

Re: new engine problems

hi you can check the timing take the valve cover off take the sparkplugs out turn the engine at top dead center ( a bit further as the timing mark ) now piston 1 and 4 are fully up if you now turn the engine a bit forwards and backwards at cyl 1 or 4 the valves must tumble i think a 1/4 inch past th...
by svramselaar
December 7th, 2019, 9:34 am
Forum: Technical Discussion
Topic: new engine problems
Replies: 40
Views: 1479

Re: new engine problems

hi if a factory make the pistons they can have different size`s you can trow them away or label them A to ? the bore off the cylinders is also a bid different in size label them as 1 to ? now you can fit a big piston at a big hole and a small piston at a small hole so the tollerance is better to han...
by svramselaar
December 6th, 2019, 10:49 am
Forum: Technical Discussion
Topic: engine bore
Replies: 12
Views: 469

Re: engine bore

hi my head has new valves and seatings the engine is in the mutt so i dont know for the bearings the oilpressure is ok clutch is new i have a engine gasket set € 25,00 4 pistons 0.20 € 175.00 rings 0.20 € 55,00 block bore to 0.20 € 240,00 cranckshaft bearings std € 75,00 if i need 0.20 bearings € 35...
by svramselaar
December 5th, 2019, 6:12 am
Forum: Technical Discussion
Topic: engine bore
Replies: 12
Views: 469

Re: engine bore

hi

Ken
is it posseble to mail me the page
if i print it i can not reed it it is to small

thanks george