Restauración A2

A place to post pics and descriptions of ongoing restoration projects

Moderators: rickf, raymond, Mr. Recovery

Hambone
Brigadier General
Brigadier General
Posts: 2495
Joined: October 1st, 2010, 12:19 am
Location: El Dorado, Arkansas

Re: Restauración A2

Unread post by Hambone » January 25th, 2021, 8:21 pm

Rupert, you are one of the fastest restorers I've seen, will it be ready next week? :lol: Hambone

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » January 26th, 2021, 2:14 pm

Hambone wrote:
January 25th, 2021, 8:21 pm
Rupert, you are one of the fastest restorers I've seen, will it be ready next week? :lol: Hambone
jajajaja how funny you are Hambone! This morning when I read it I was laughing :lol: :lol: :lol: :lol:
We can take a little spin tomorrow :wink: :wink: :wink:

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » January 27th, 2021, 1:30 pm

I continue with the ground under the gas tank, these pieces were practically missing, and the little that was left fell off just by touching it, this time I couldn't make a piece like the one I did with the toolbox, it was impossible for me, very big, with many different shapes and had to fit the tank without too much excess.

In the end I decided to make two pieces but with the curves made more angular. Let's go with the images.
IMG_20190216_125350.jpg
First I drew on the sheet metal sheet and then I was cutting and folding and checking that the deposit has to fit inside, without being too big.
IMG_20190216_105356.jpg
IMG_20190210_121911.jpg
The one you see on the left of the image I passed a little with the radial through some folds to facilitate the folding, I would not do it again, it feels a little weaker, then I had to give it a little consistency.
IMG_20190304_155923.jpg
On this sheet metal floor I have pasted a tape that has a sponge to prevent any possible friction, (I do not know if there will be, it is difficult to know for sure)

Then I made these covers, which go over the central cross member of the car, between the rear floor and the seats.
IMG_20190310_125435.jpg
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » January 27th, 2021, 2:14 pm

Here I have the welded covers, with this thick plate that the car had in the middle joining the structure.
IMG_20190310_192241.jpg
I feel that the image is so blurry but I have no other that looks better, this piece of floor is the only one that I have been able to reuse, it was a little dented but without rust.
I took advantage of the drills I made to remove the previous points to give the new points, then I gave it a very strong structural adhesive to delimit the piece well since the edge was a bit sinuous and I wanted to make it more straight
IMG_20190323_122916.jpg
I have added a bit of sealer by brush in this previous repair, I suppose that with the primer it was already protected but if the primer did not reach a small gap, the sealer by brush will prevent moisture from reaching. on the inside I added cavity wax, actually in each interior hollow that has remained of the car even though it is primed I have given cavity wax.
IMG_20190406_175638.jpg
Then it was the turn of the rear floor, same operation, measure and mark very carefully to drill right where it is, and not in a vacuum, from under the car you can draw the lines of the edges of the structure to make the holes without going out .
Then I laid the floor and marked where the solder points will go.
IMG_20190406_213944.jpg
I removed it, filed the primer on all three faces and put it back to weld, I screwed in areas again and welded the weld points spaced apart to avoid expansion and deformation. Everything has been fine, there is no strange bulge, all the edges are in place and the piece has a flange in va mounted in the central part of the car that is also very well mounted, in the last image you can see ...
IMG_20190406_213957.jpg
As it goes, it looks like a car! :lol: :lol: :lol: :lol:
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » February 7th, 2021, 3:49 pm

To "finish" the body, it is time for the rear, it is made up of several pieces.
First I have welded the new lower part, inside it has a reinforcement around the trailer hitch bolts, I have made them new because this part of the car was very bad inside.
IMG_20190519_171216.jpg
Then it takes another piece similar to a Z, also for the support of the trailer hitch
IMG_20190704_114146.jpg
And finally the complete rear part, these parts are new but the car has the same, same size and same shape, when my car arrived it had rust holes and I did not know the parts and holes behind, here the holes are clear what's up...
If the rust has come out of the body from the inside, I am almost certain that you will have rust even behind the piece that I welded in the first photo, at least in my case it was like that, you cannot get there without removing all this.
IMG_20190704_213436.jpg
IMG_20190704_213457.jpg
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » February 7th, 2021, 8:00 pm

As you know ... to weld, you have to file the plates and after welding that piece of the weld is filed and burned, in the joints it cannot be primed because the plates are overlapped and the primer does not enter, it could not leave all those Unprotected welds and filings without further ado, I decided to seal everything that I welded to prevent water from reaching as much as possible.
IMG_20190705_094815.jpg
Although I have only put an image, I have sealed everything I have welded.
After I have painted the underbody (Anti gravel), I have also applied this paint in the area of the feet and in the back ...
IMG_20191110_090849.jpg
IMG_20191110_090635.jpg
I have given a coat of putty to the joints of the new sheets so that the welds and the fins are not noticeable because they were a little wrinkled and it would be a bit ugly, then I have given it a primer, this time with a color that facilitates covering for the final color
IMG_20191117_133334.jpg
IMG_20191117_133354.jpg
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » February 7th, 2021, 8:26 pm

To paint the final color I wanted to have it on the ground with the wheels on so I had to do a bit of mechanics before finishing the painting.
IMG_20191214_194230.jpg
Parts are beginning to arrive, in the front and rear suspensions I have changed the 8 wheel bearings for timken ones just like the ones I had, I have also changed the 8 bearings seals, the 12 silent blok of the front and rear suspension arms, the 8 silent blocks of the front shock absorbers, 4 front shock absorbers, the new rear shock absorbers, the brake hoses, brake shoes and brake pistons ... damn mutt! it was not worth its weight in junk !!
IMG_20200105_134931.jpg
After mounting all of this I was finally able to put it down!
IMG_20200301_150102.jpg
And now paint! I was undecided for a long time, it was tempting to paint it in olive green with the inscriptions and stars, it is an easy painting, all green, but very common, at least in Spain ...
I really liked the MERDC camouflage, it is beautiful and it is not usual, but it seemed difficult to paint and also the annoyance that when I have to repaint in the future, I will have to repaint in several colors. But hey, in the end I decided on what I liked the most, even if it was more complicated and annoying ...
IMG_20200521_192834.jpg
IMG_20200514_215635.jpg
I'm happy, I think it was painted well and at no time have I thought about leaving it green because I like it that way!
You do not have the required permissions to view the files attached to this post.

acudanut

Re: Restauración A2

Unread post by acudanut » February 17th, 2021, 7:38 am

Very nicely done sir !!

Mark
Brigadier General
Brigadier General
Posts: 2085
Joined: September 19th, 2009, 11:33 pm
Location: South Dakota

Re: Restauración A2

Unread post by Mark » February 17th, 2021, 2:22 pm

I would say there was never a paint job looking that good on a 151 in the Armed Forces!
mark


1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » March 4th, 2021, 9:21 am

acudanut wrote:
February 17th, 2021, 7:38 am
Very nicely done sir !!
Mark wrote:
February 17th, 2021, 2:22 pm
I would say there was never a paint job looking that good on a 151 in the Armed Forces!
Thanks guys! soon I will upload more images

acudanut

Re: Restauración A2

Unread post by acudanut » March 7th, 2021, 3:18 pm

One of the best jobs, I have ever seen. !!

Cisco82
Sergeant First Class
Sergeant First Class
Posts: 202
Joined: March 22nd, 2012, 6:50 am
Location: ITALY

Re: Restauración A2

Unread post by Cisco82 » March 8th, 2021, 4:58 pm

Wonderful work! ur metal works are really good , i would like to be so good with welding and sheet works!
Francesco

M151-A1 1969
Alfa Romeo AR-51 1952

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » March 20th, 2021, 6:45 pm

acudanut wrote:
March 7th, 2021, 3:18 pm
One of the best jobs, I have ever seen. !!
Thanks! It has been a really long and rewarding job! I actually enjoy it, that's why I bought it such a bad mutt.
Cisco82 wrote:
March 8th, 2021, 4:58 pm
Wonderful work! ur metal works are really good , i would like to be so good with welding and sheet works!
Everything is getting! A good welder is basic to weld well, the rest is practice and repair processes. :D :D :D

We continue, today a bit of differentials ...

It was evident that in a car in poor condition like mine was when I bought it, you had to take a look at the differentials, well, I filled them with valvulin to check if they came off, I left them for a while and the result was that yes, the checkpoints were coming out. It was predictable and I already had the seal kit for both differentials ...
It was the best I could do, they had a lot of finless brown trout and also one of the bearings was bad ... it was going to last a short time so I changed it, the other bearings seemed fine and I left them.

Al lio!!

Cleaning first, remove the adjusting crowns to clean well and see the bearings.
IMG_20200525_192713.jpg
IMG_20200525_194214.jpg
And reassemble
IMG_20200525_194601.jpg
IMG_20200526_123900.jpg
Wear sleeves
IMG_20200526_114334.jpg
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » March 20th, 2021, 7:03 pm

Finished here, with all new seals
IMG_20200526_151913.jpg
Now the next one.
In this case, the valve inside the differential revealed that something was not right, a small amount came out and in addition to being light gray, I can imagine that at some point water entered the differential.

And here the result, rusty bearing ... I had to change it.
IMG_20200526_180652.jpg
IMG_20200526_181037.jpg
The two finished preparing for painting, cleaning, sanding and re-cleaning.
IMG_20200529_171620.jpg
IMG_20200529_171654.jpg
You do not have the required permissions to view the files attached to this post.

rupert's
Master Sergeant
Master Sergeant
Posts: 337
Joined: March 29th, 2020, 7:10 am
Location: España

Re: Restauración A2

Unread post by rupert's » March 20th, 2021, 7:11 pm

Yyy ... job finished, refilled and no leaks
IMG_20200529_201616.jpg
Turn of the exhaust pipe, I bought it whole, I decided to paint it black with heat paint and leave the tip of the exhaust a metal color ...
IMG_20200815_084924.jpg
IMG_20200820_102252.jpg
IMG_20200820_102300.jpg
IMG_20200820_102323.jpg
You do not have the required permissions to view the files attached to this post.

Post Reply