Generic jeep
Moderators: rickf, raymond, Mr. Recovery
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Generic jeep
Thought I would start on the Texas jeep since it will be a fairly easy rebuild, I know it's not a M151 but it is close, at least it's not an Encore. Going to replace the floors in it, they are just flat metal so they can be easily sheered at the local sheet metal shop, sorry Guy. Here are a few photos of it.
Tranny may need a little attention
The dimmer switch cover was made of fiberglass
I like how they mounted the taillight, just separate the light and mount, no mounting bracket needed.
Torched out seat mounts
Receiver hitch already installed
Custom muffler support
Tranny may need a little attention
The dimmer switch cover was made of fiberglass
I like how they mounted the taillight, just separate the light and mount, no mounting bracket needed.
Torched out seat mounts
Receiver hitch already installed
Custom muffler support
-
- Brigadier General
- Posts: 2037
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Generic jeep
I'll let it slide this time Buddy! Looks like a fun project.
Guy
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: Generic jeep
I had heard the Titan's were 11 gauge steel, it does look pretty thick.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
It is heavy metal, not sure what gauge it is yet, does anyone have a good process for removing undercoating? the best way I have found is with a little heat and a scraper, if I have to do it this way, I will have to move it outside, I think I caught a buzz in 5 minutes. I'm thinking about having it sand blasted but not sure how well the blasting will cut this crap, any suggestions?? Hambonerickf wrote:I had heard the Titan's were 11 gauge steel, it does look pretty thick.
Re: Generic jeep
I just seen a guy use dry ice, he lays it on, then hits the area with a hammer, then scrapes easily out with a scraper,I just put the issue on the internet it shows the answers(youtube) hope this works for you
mark
1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416
1968 m274A5
1960 m151
1981 m151A2
1964 m416
1971 m416
Re: Generic jeep
Have you tried paint stripper? Try the heat from underneath, that works great for bondo and you don't have to heat up the undercoating as much.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2037
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Generic jeep
I would think a good sand blasting would be the easiest way. And with the fact that the body is heavy duty you don't have to worry about blowing holes in it or warping it.
Guy
Guy
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
I'm not a sandblasting guru but I was told it was hard to get off, I have a friend that will do it for me if I buy the diesel, sand and beer. I'm going to try paint remover vs. heat gun tomorrow, I will keep you posted.lpcoating wrote:I would think a good sand blasting would be the easiest way. And with the fact that the body is heavy duty you don't have to worry about blowing holes in it or warping it.
Guy
-
- Staff Sergeant
- Posts: 166
- Joined: July 12th, 2014, 11:55 am
- Location: Kansas
Re: Generic jeep
I had the original undercoating on mine and we took it to a commercial sand blasting place and it came out very good. Go to my thread in the restoration section and you can see it. LarryHambone wrote:I'm not a sandblasting guru but I was told it was hard to get off, I have a friend that will do it for me if I buy the diesel, sand and beer. I'm going to try paint remover vs. heat gun tomorrow, I will keep you posted.lpcoating wrote:I would think a good sand blasting would be the easiest way. And with the fact that the body is heavy duty you don't have to worry about blowing holes in it or warping it.
Guy
active duty 63-66
Sgt A Co. 385th M.P. Bn.
62 M151
64 M274A1
62 Chevy
31 Chevy
MVPA Member
VFW
America Legion
Sgt A Co. 385th M.P. Bn.
62 M151
64 M274A1
62 Chevy
31 Chevy
MVPA Member
VFW
America Legion
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
The aircraft stripper works fine with 2 coats.
-
- Brigadier General
- Posts: 2037
- Joined: February 19th, 2013, 11:38 pm
- Location: Mansfield, PA
- Contact:
Re: Generic jeep
Gloves!!! That stuff is nasty. Make sure you have good ventilation. I would wear a respirator as well.
M151 Body Panels - http://www.m151bodypanels.com/
'68 A1 - Under full resto
'68 A1 - Under full resto
Re: Generic jeep
Yes Gloves, that stuff is lye and will take skin off as well as it does paint! And it does wonders for lungs and emphysema is no fun, trust me on that one.
1964 M151A1
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
1984 M1008
1967 M416
04/1952 M100
12/1952 M100- Departed
AN/TSQ-114A Trailblazer- Gone
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
I had my gloves on, just took them off for pic, had shop doors open, fumes were not a problem, it's 70 degrees here, gonna try to get some more done tonight.rickf wrote:Yes Gloves, that stuff is lye and will take skin off as well as it does paint! And it does wonders for lungs and emphysema is no fun, trust me on that one.
-
- Brigadier General
- Posts: 2519
- Joined: October 1st, 2010, 12:19 am
- Location: El Dorado, Arkansas
Re: Generic jeep
I was able to get 1 side done tonight, hope I don't bore you with the photos, think I'm going to put rhino back on the floors, hope I don't have to take it back off again.
P.S. the cattle guard has to go.
P.S. the cattle guard has to go.
-
- Master Sergeant
- Posts: 377
- Joined: October 28th, 2009, 10:37 am
- Location: Ypsilanti Michigan
Re: Generic jeep
Nothing like getting stoned off of aircraft paint remover....
1966 M151A1 ___All matching '44 M1 Garand
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ
1951 H&R M1 Garland__1966 Fairlane GTA
1973 Torino wagon_____1942 03A3 - Unissued
1939 Unissued 1903____1944 M1 Inland Carbine
1966 M-16____________1943 1911A1
1918 Model 1917 .45 Revolver
1943 M1 Quality Hardware Carbine
1967 Saginaw 1919A6
1943 Saginaw 1919A4
1952 M1C and M1D Garands
KD8QEQ